General Service
PWC GENERAL SERVICE
|- Replace engine oil and filter
|- Replace engine spark plugs
|- Check air filter (if equipped)
|- Lube and adjust steering cable
|- Lube and adjust reverse cable (if equipped)
|- Check battery and test charging system
Battery__________ Charging__________
|- Check steering master
|- Check and adjust Trim System (if equipped)
|- Check and adjust throttle cable
|- Check throttle shaft
|- Check OTAS system operation (if equipped)
|- Check iBR / RiDE operation (if equipped)
|- Check supercharger operation (if equipped)
|- Check intercooler for leaks (if equipped)
|- Lubricate intermediate housing (YAM)
|- Check and tighten nuts and hardware
|- Lubricate and inspect carbon ring (SD driveshaft hull seal)
|- Check and tighten exhaust hose clamps inspect for rust
|- Connect OEM Diagnostic equipment to check for fault codes
|- Clean water inlet strainer and bilge strainer
|- Check and clean water separator
|- Reset service indicator
|- Spray engine with corrosion block
|- Check cooling system and top off coolant (SD)
|- Perform general safety inspection
|- Check VIN for open recalls
|- Run unit of flush check for leaks
YAMAHA JET BOAT GENERAL SERVICE
|- Replace engine oil and filter
|- Replace engine spark plugs
|- Check air filters
|- Lube and adjust steering cables and nozzles
|- Check jet pump anodes (zincs)
|- Lube and adjust reverse cables and gates
|- Check battery and test charging system
|- Check and adjust throttle cables
|- Check throttle shaft
|- Lubricate intermediate housing
|- Check gauges switches and breakers
|- Check all running and navigation lights
|- Check and verify bilge pump operation
|- Check all locker hinges and screws
|- Check and tighten nuts and hardware
|- Connect Y.D.I.S check for fault codes and verify hours
|- Run unit of flush check for leaks
|- Clean water inlet strainer
|- Check and clean water separator
|- Perform general safety inspection
|- Check VIN on Y.D.S check for open recalls
|- Replace engine oil and filter
|- Replace engine spark plugs
|- Check air filter (if equipped)
|- Lube and adjust steering cable
|- Lube and adjust reverse cable (if equipped)
|- Check battery and test charging system
Battery__________ Charging__________
|- Check steering master
|- Check and adjust Trim System (if equipped)
|- Check and adjust throttle cable
|- Check throttle shaft
|- Check OTAS system operation (if equipped)
|- Check iBR / RiDE operation (if equipped)
|- Check supercharger operation (if equipped)
|- Check intercooler for leaks (if equipped)
|- Lubricate intermediate housing (YAM)
|- Check and tighten nuts and hardware
|- Lubricate and inspect carbon ring (SD driveshaft hull seal)
|- Check and tighten exhaust hose clamps inspect for rust
|- Connect OEM Diagnostic equipment to check for fault codes
|- Clean water inlet strainer and bilge strainer
|- Check and clean water separator
|- Reset service indicator
|- Spray engine with corrosion block
|- Check cooling system and top off coolant (SD)
|- Perform general safety inspection
|- Check VIN for open recalls
|- Run unit of flush check for leaks
YAMAHA JET BOAT GENERAL SERVICE
|- Replace engine oil and filter
|- Replace engine spark plugs
|- Check air filters
|- Lube and adjust steering cables and nozzles
|- Check jet pump anodes (zincs)
|- Lube and adjust reverse cables and gates
|- Check battery and test charging system
|- Check and adjust throttle cables
|- Check throttle shaft
|- Lubricate intermediate housing
|- Check gauges switches and breakers
|- Check all running and navigation lights
|- Check and verify bilge pump operation
|- Check all locker hinges and screws
|- Check and tighten nuts and hardware
|- Connect Y.D.I.S check for fault codes and verify hours
|- Run unit of flush check for leaks
|- Clean water inlet strainer
|- Check and clean water separator
|- Perform general safety inspection
|- Check VIN on Y.D.S check for open recalls
MOTORCYCLE GENERAL SERVICE
_____SPORTBIKE / CRUISER_____
|- Change engine oil and filter
|- Replace drain plug washer
|- Replace rear axle fluid if applicable
|- Replace transmission fluid if applicable
|- Clean, lube and adjust chain, or check belt
|- Check and fill all hydraulic fluids.
|- Test battery and check charging system
Battery Health___________
Battery voltage__________
Charging ________
|- Check / Torque steering head
|- Check coolant if applicable
|- Inspect & air tires and advise on wear
Front Pressure_________ Rear pressure________
Front Wear __________ Rear Wear _________
|- Inspect front & rear brakes advise on wear
Front Brake ___________ Rear Brake ________
|- Inspect all fuel and brake lines
|- Inspect front fork assemblies
|- Check chassis hardware
|- Inspect / Adjust clutch to specs
|- Verify proper idle RPM.
|- Check for trouble codes if applicable
|- Clear maintenance indicator if applicable
|- Check all linkages, cables and hoses, including fuel line & filter.
|- Grease all fittings and lube all pivot points
|- Check all lighting & accessory functions..
|- Test ride bike to verify overall drivability & safety condition of bike
|- Run VIN and check for any updates or recalls
CAN-AM SPYDER GENERAL SERVICE
----------------------------------------------------------------------------------------------
|- Replace engine oil and oil filter.
|- Check clutch fluid level (SM6 model only).
|- Check brake fluid level.
|- Check reverse mechanism operation.
|- Check engine coolant level.
|- Inspect throttle twist grip operation.
|- Check battery
Health_________ Voltage________ Charging ________
|- Check lighting system (brake light, hazard warning light, turn signal lights, position lights, license plate light).
|- Clean brake light switch.
|- Check operation of control switches.
|- Inspect the drive belt condition and its tension. Adjust if required.
|- Check tightening torque of the front wheels lug nuts.
|- Check tightening torque of the rear wheel axle nut.
|- Check parking brake operation. Adjust as required.
|- Check wheels wear. Align front wheels if required.
|- Check tire pressure. Adjust as required
Left Front tire_______ Right front tire_______ Rear tire______
Pressure LF_______ RF ________ Rear_________
|- Check brake pads and discs condition.
Front pad wear______ Rear pad wear _________
|- Check passenger handholds looseness.
|- Check footrest looseness.
|- Check body panels looseness.
|- Check operation of storage compartment latches, hinges and key barrels.
|- Check and retighten exhaust pipe, clamping rings, joints, and gaskets condition.
|- Using BRP Utility and Diagnostic Software (B.U.D.S.), check |- fault codes and install required updates.
_____SPORTBIKE / CRUISER_____
|- Change engine oil and filter
|- Replace drain plug washer
|- Replace rear axle fluid if applicable
|- Replace transmission fluid if applicable
|- Clean, lube and adjust chain, or check belt
|- Check and fill all hydraulic fluids.
|- Test battery and check charging system
Battery Health___________
Battery voltage__________
Charging ________
|- Check / Torque steering head
|- Check coolant if applicable
|- Inspect & air tires and advise on wear
Front Pressure_________ Rear pressure________
Front Wear __________ Rear Wear _________
|- Inspect front & rear brakes advise on wear
Front Brake ___________ Rear Brake ________
|- Inspect all fuel and brake lines
|- Inspect front fork assemblies
|- Check chassis hardware
|- Inspect / Adjust clutch to specs
|- Verify proper idle RPM.
|- Check for trouble codes if applicable
|- Clear maintenance indicator if applicable
|- Check all linkages, cables and hoses, including fuel line & filter.
|- Grease all fittings and lube all pivot points
|- Check all lighting & accessory functions..
|- Test ride bike to verify overall drivability & safety condition of bike
|- Run VIN and check for any updates or recalls
CAN-AM SPYDER GENERAL SERVICE
----------------------------------------------------------------------------------------------
|- Replace engine oil and oil filter.
|- Check clutch fluid level (SM6 model only).
|- Check brake fluid level.
|- Check reverse mechanism operation.
|- Check engine coolant level.
|- Inspect throttle twist grip operation.
|- Check battery
Health_________ Voltage________ Charging ________
|- Check lighting system (brake light, hazard warning light, turn signal lights, position lights, license plate light).
|- Clean brake light switch.
|- Check operation of control switches.
|- Inspect the drive belt condition and its tension. Adjust if required.
|- Check tightening torque of the front wheels lug nuts.
|- Check tightening torque of the rear wheel axle nut.
|- Check parking brake operation. Adjust as required.
|- Check wheels wear. Align front wheels if required.
|- Check tire pressure. Adjust as required
Left Front tire_______ Right front tire_______ Rear tire______
Pressure LF_______ RF ________ Rear_________
|- Check brake pads and discs condition.
Front pad wear______ Rear pad wear _________
|- Check passenger handholds looseness.
|- Check footrest looseness.
|- Check body panels looseness.
|- Check operation of storage compartment latches, hinges and key barrels.
|- Check and retighten exhaust pipe, clamping rings, joints, and gaskets condition.
|- Using BRP Utility and Diagnostic Software (B.U.D.S.), check |- fault codes and install required updates.
